Skip to Content
Go back
BAS-IP / Articles / General / Power Up Your Projects: How BAS-IP’s Built-in Energy Booster Can Change the Game for Low-Voltage Installers
reading time: 5 mins

Power Up Your Projects: How BAS-IP’s Built-in Energy Booster Can Change the Game for Low-Voltage Installers

Tired of dealing with extra power supplies and tangled wires for electromechanical locks? What if you could simplify your installations, improve reliability, and save time on every job? Low-voltage installers dealing with door entry and access control will find the answer in BAS-IP’s innovative Built-in Multiplying Energy Booster.

This is more than just a minor tweak; it represents a fundamental shift in how electromechanical locks are powered and protected. This distinct market differentiator is seamlessly integrated into BAS-IP’s advanced individual entry panels, such as the AV-08FBL and the new AV-08FBIL, to answer direct questions from installers about how it works.

Beyond the Fundamentals: The Technical Brilliance of the Multiplying Energy Booster

The Multiplying Energy Booster is fundamentally a sophisticated, integrated electronic module. It consists of a meticulously engineered array of microchips, transistors, diodes, and capacitors. This is a proprietary, intelligent power management system that is integrated into the internal architecture of the panel rather than being an external component that comes with it.

The Technical Edge’s Method of Operation:

  • Peak Delivery & Energy Accumulation: The booster effectively stores and actively gathers energy. This stored energy is instantly released as a strong impulse when an electromechanical lock requires a sudden spike in power to activate (that critical “peak load”), guaranteeing consistent, clear lock operation.
  • Intelligent Lock Protection: This system protects your entire setup, not just the power supply. The electromechanical lock is actively shielded by the booster from:
    • By carefully controlling power delivery, overheating and burnout can be prevented.
    • extended voltage/current supply, avoiding damage from constant power.
    • wiring mistakes, preventing problems caused by erroneous activation settings.
  • Simplified Wiring & Extended Cable Runs: The “multiplying energy” feature enables you to connect electromechanical locks to the panel directly with cable runs up to 7–10 meters (23–33 feet) without the lock requiring an extra power source! This significantly reduces material costs and wiring complexity.
See also  Intercom Multi-Factor Authentication (MFA)

Opening Up Unmatched Benefits for Installers

Your company and your clients will directly benefit from this integrated solution in the following ways:

  • Ultimate Simplicity: Control and power the lock directly through a single “Lock” output from the BAS-IP panel. No more separate power supplies or external relays are needed.
  • Reduced Costs: Eliminate the expense of purchasing and installing additional power supplies and relays for electromechanical locks. Less hardware equals lower costs.
  • Faster Installation: You can finish more projects more quickly and with fewer connection errors when there are fewer parts and simpler wiring.
  • Improved Reliability & Protection: Inbuilt safeguards reduce service calls and maintenance hassles by protecting the lock against common installation errors, overloads, and premature wear.
  • PoE Compatibility: The Multiplying Energy Booster works flawlessly, ensuring a clean, efficient power delivery even if your BAS-IP panel is powered via PoE (IEEE802.3af standard).

A Very Special Advantage: No Similar Products on the Market

This technology’s distinctiveness in the intercom market is what really makes it stand out. The BAS-IP Built-in Multiplying Energy Booster is a groundbreaking innovation that is integrated right into the entry panel, unlike other systems that require external power units, independent relays, or special wiring for electromechanical locks. This implies that other solutions won’t offer this degree of direct electromechanical lock support and embedded intelligent power management. A genuine differentiator, it optimizes your workflow in a manner that no other vendor presently provides.

Some of our most well-liked and adaptable models, such as the BAS-IP AV-08FBL and the recently released BAS-IP AV-08FBIL panels, incorporate this state-of-the-art technology.

Ideal for Smaller Projects: Optimizing Cost Savings

See also  Door Buzzer Entry Systems: Fortify Your Property

For small to medium-sized projects where every little detail and every dollar saved truly matters, this technology is the perfect option:

  • Private residences and townhomes: ideal for electromechanically operated front doors and gates. A neat installation free of unsightly extra boxes or cables will be achieved. This immediately lowers your labor and equipment budget.
  • Small Offices & Retail Stores: Fast installation is essential for storage spaces or main entry doors. Businesses with limited funds benefit greatly from the process’s speed and lower material costs caused by simpler wiring and fewer components.
  • Warehouses and Technical Areas: Regulating access to storage spaces or service entrances where dependability and economy are crucial. You can finish projects more quickly and profitably by reducing the amount of time needed to install and configure each access point.

The removal of external power units and relays becomes the most evident and palpable savings factor in these situations, where frequently only one or two locks are required.

Connecting Your Locks: Essential Information

The “Lock” output on the supported BAS-IP panels is designed for electromechanical locks only with the following specifications:

  • Voltage: 12–14 V
  • Current Consumption: Up to 3.5 A (recommended)
  • Cable Length: The lower the lock’s current consumption, the greater the permissible cable length.
    • For locks up to 3.5 A, a cable length of up to 5–7 meters (16–23 feet) is recommended for stable operation.
    • You can still connect locks with higher current draws (4.0–4.5 A, for example) directly, but the suggested cable distance should be lowered to 3–4 meters (10–13 feet).

Minimum Power Requirements for the Panel:

  • A 12V, 1A power source or PoE (IEEE802.3af standard) is needed for the panel itself.
  • A 12V, 2A power supply or the same PoE standard is advised for best results.
See also  Remote Door Access: Discover 11 Revolutionary Features

An example of clever engineering that was created with the installer in mind is the BAS-IP Built-in Multiplying Energy Booster. It increases the overall dependability of your access control solutions, protects your installations, and expedites your work. With BAS-IP, enter a new era of reliable, easy-to-use, low-voltage installations.

similar articles
Articles
Accessible entry for everyone: why BAS-IP AV-08FBIL is suitable for government and municipal projects

The entry panel is the first point of contact between a building and a person. And if this building is municipal, social, medical, or educational, the panel at the entrance must be clear and convenient for everyone: the hard of hearing, the visually impaired, elderly people, visitors unfamiliar with the system. AV-08FBIL was designed precisely […]

Read More
Articles
What Is a Video Intercom Monitor and How Does It Work?

A video intercom monitor is often treated as just a screen on the wall. In reality, it is one of the key parts of the system: it is the device through which the user receives the call, sees the visitor, speaks with them and manages access. What a Video Intercom Monitor Is A video intercom […]

Read More
Articles
What SIP Is in Intercom Systems: A Simple Explanation

When the word “SIP” appears in the specifications of an intercom or entry panel, it often sounds like something purely technical. In practice, the meaning is much more practical. SIP is a protocol used to establish communication between devices on a network. Put simply, it helps one system “call” another, establish a connection, and begin […]

Read More
Articles
What Is an IP Video Intercom

When people first come across the term “IP video intercom,” it often sounds more technical than it really is. In practice, the basic idea is fairly simple. An IP video intercom is an intercom system that works over a network. In other words, communication between the entry panel, the indoor monitor, and other devices is […]

Read More
Articles
What Is an Entry Panel and What Does It Do?

An entry panel is often treated as just “the button by the door.” In reality, it is one of the key elements of the intercom system. It is the device through which a call begins, audio and video are carried, and, in some cases, access, identification, and different entry scenarios are handled. So it is […]

Read More
Articles
What Access Control Is and How It Relates to a Video Intercom

Access control and a video intercom are often treated as though they were the same thing, because both are linked to entering a building. But they are not quite the same. A video intercom is primarily about communication with a visitor: the call, the conversation, the image, and the decision to release the door. Access […]

Read More
Articles
What PoE Is and Why It Is Useful for IP Intercoms

What PoE Means in Simple Terms PoE stands for Power over Ethernet. Put simply, it means that the same Ethernet cable can carry both data and power. That means that, for some devices, you do not need a separate network connection and a separate power feed. If the equipment supports PoE, one cable may be […]

Read More
Articles
How an IP Video Intercom Differs from an Analogue One

Why This Comparison Is Often Presented Too Simplistically When people talk about the difference between an IP and an analog video intercom, the discussion is often reduced to a crude formula: analog is basic and outdated, while IP is automatically modern and better. That is a convenient story if someone only wants to sell IP […]

Read More
Articles
What to Look for When Choosing an Entry Panel for Outdoor Use

Start Not with the Design, but with the Use Scenario The most common mistake is choosing an entry panel without a clear task in mind. A panel for a private house, a block of flats, an office, or a commercial site is not the same thing. First, answer the basic questions: How many users will […]

Read More
Articles
Flush-Mounted or Surface-Mounted Entry Panel: Which Should You Choose?

What the Difference Actually Is A flush-mounted panel is recessed into the wall or into a prepared niche, so only the front face remains visible from the outside. That makes the installation look neater and more integrated. A surface-mounted panel is fixed on top of the wall. It protrudes further, but it is usually much […]

Read More